2.2KW ATC Water Cooled Spindle Motor Automatic Tool Changer ISO20+VFD Drive 220V

Description: 2.2KW ATC Water Cooled Spindle Motor Automatic Tool Changer ISO20+VFD Drive 220V Package include:1). 2.2KW ATC Spindle (220V)Package include:1 x 2.2KW ATC Automatic Tool Change Spindle Motor 80mm ISO20 220V,24000rpm1 x ISO20-ER20 tool holder with pull stud User manual 2). 2.2KW ATC Spindle+VFD (220V)Package include:1 x 2.2KW ATC Automatic Tool Change Spindle Motor 80mm ISO20 220V,24000rpm1 x 2.2KW Fuling Brand VFD Inverter 220V (High Quality)1 x ISO20-ER20 tool holder with pull stud User manual I. 2.2KW ATC Automatic Tool Change Spindle Motor 220V,24000rpm1. Product overview 1) This spindle is built-in type spindle motor, built-in three asynchronous motors,by theinverter control.As the spindle has a compact structure,high power, big torque, small vibration,low noise characteristics,so it can achieve high speed,high powe cutting,high precision and highstability operation.2) The bearing of spindle use grease lubricated angular to contact bearings,can beachieved lifelong lubricating within the life cycle.3) The spindle use forced coolling mode to coolling motor,front and rear bearings.Coolantflow through the reasonable arrangement cycle watercourse of the spindle body,thus can takethe heat generated of the spindle rotation speed, to achieve thermal equilibrium,let spindletemperature within a certain constant value. External cooling device effect:maintaining aconstant temperature of the coolant.4) The spindle built-in PTC 140 temperature sensor(Technical parameters are visible inother sections of this specification),you can read it anytime if you need to protect the motortemperature.5) The tool clamping methods:this spindle built-in automatic tool change device,shank formis ISO20 Spindle modelRTM80-20-24Z/2.2 220VVoltage220VMaximum speed24000rpmRated frequency400HzElectric current6.4AMotor pole2 poleRated power1.8KW (S1)Peak power2.2KW (S6)Rated torque0.59NmPeak torque0.84Nm 2. Drawing Size Description Technical parametersSpindle blowing dust/seal gas pressure (MPa)0.2-0.25Spindle gas seal gas flow(L/min)65±10 (When on Working)Cooling water pressure (MPa)>=0.25Cooling water flow (L/min)>=2.5Cooling water temperature deg24-28Spindle static state pulse (µm)<=3Spindle vibration (mm/s)<=0.8Spindle diameter (mm)dia 80 (0/-0.02)Motor windings Pressure test (V/M)1000V/1 minute withstanding Voltage testTool InterfaceISO20Inverter Specifications2.2KW (220V)FitmentFor castings, aluminum, glass, etc., and other processingSpindle installation explanation1) Circulating Cooling System DescriptionThe system must ensure that the cooling water temperature of supply spindle is between 24-28deg. Usually setting the flow switch in return pipe of the cooling system,to ensure the supply of spindle cooling water. Cooling water requirements: we recommend using distilled water, while recommend Feinuokesi (Fenix) protective agent F1 (using the scale of 1: 200),coolant temperature is 26deg±2deg,inlet, outlet pipe temperature can’t exceed 5 deg.It is allowed As long as other monitoring can ensure fuller spindle cooling.2) Air sealing controlIn order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,the gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration.3) Compressed gas quality requirementsThe quality requirement of gas which is used in gas seals:Oil content:<0.01mg/m3Solid particle:<5µ mPressure dew point: <7.5deg(0.7MPa)4) Running-in program instructionsOnly all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle.Note: New or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase to 50% of the maximum speed,to run 15 minutes,finally, increase to maximum speed.It’s need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department. II. 2.2KW Fuling Brand Inverter VFD Tech parameters:1) Input Voltage: 220V2) Output Voltage：0- 220V3) Input Frequency: 50/60 Hz4) Output Frequency: 0-1000 Hz5) Input Phase: 1 phase or 3 phase6) Output Phase: 3 phase7) Warranty: 3 year from the date you purchased Shipping Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately Items will be shipped within 1-2 days upon the receipt of payment. Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. We are a new member in ebay now, and need understand both of sides Refund When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost Contact us Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s message within 1-2 business days,if not pls check the mail box again Customer’s satisfaction is very important to us.

Price: 1490 USD

Location: Changzhou

End Time: 2023-12-01T03:18:15.000Z

Shipping Cost: 0 USD