Happymodel ELRS AIO 5in1 Flight Controller Built-in SPI 2.4G ELRS RX Receiver

Description: HM-CB180-Z-15 Zahnrad-Satz für Walkera CB180D \ 180Q \ 180Z V200DQ01 Hubschraube3.99 EURFree shippingRS232 RS485 Seriell zu WiFi und Ethernet Konverter USR-W610 TCP Server / TCP45.59 EURFree shippingQX-MOTOR 12-Blade 64mm Impeller EDF mit gefächertem Fasszubehör3.99 EUR0.8 EURUSRIOT USR-TCP232-304 Serial RS485 to TCP/IP Ethernet Server Converter Module21.99 EURFree shippingFlysky FS-iA10B 10CH Empfänger für FS-i6 FS-I6 FS-I4 FS-i10 FS-iT4S Sender20.79 EURFree shippingJEYI M2 M2PLUS for NGFF NVME m. 2 Transfer 2230, 2242, 2260, 2280 Adapter3.58 EUR0.8 EUR Happymodel ELRS F4 2G4 AIO 5in1 Flight controller built-in SPI 2.4GHz ELRS RXThe world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.Bind procedure:1. Power the flight controller by connecting USB. Please make sure that the port driver of the flight controller is correctly installed on the computer, then open Betaflight Configurator(Latest version) to connect, enter to the "receiver" interface, and then click "Bind Receiver", the red LED at the bottom of the flight controller will flash quickly, which means that the SPI ELRS receiver enters the bind mode. There is another way to make the receiver enter the bind mode: after connecting to the Betaflight configurator, move to the CLI interface and enter "bind_rx" in the command line.2. After correctly connecting the ES24TX or ES24TX Lite/Slim module or DIY 2.4G ELRS TX module to your Opentx radio transmitter, copy the latest version of ELRS.LUA file to the SD card in the remote controller. The directory is "SD Card/Scripts/tools", Then run ELRS.LUA and upgrade the specified TX frimware through Wifi, and then click "bind" to link with the SPI ExpressLRS receiver. Note: You need to adjust the Packet Rate to 500Hz from the ELRS interface of your radio controller before binding.3. After the binding is successful, the Red LED at the bottom of the flight controller will getting to be solid, and the telemetry can be received at the same time.4. The meaning of the LED status of the SPI receiver: the LED is getting to be solid, indicating that the bind is successful or the connection and communication is normal, the LED flashing quickly indicates that the receiver is in binding mode, and the LED flashing slowly indicates that the there is no signal received from the radio controller.Specifications: Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH)Sensor: MPU-6000(SPI connection)Original whoop size compatiblePower supply: 1S battery input (DC 2.9V-4.35V)Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 readyBuilt-in Betaflight OSD(SPI Control)Built-in 5.8G VTXBuilt-in SPI ExpressLRS 2.4GHz receiver Built-in 5V 1A BEC Flight controller firmware target: CRAZYBEEF4SX1280 Onboard 4in1 ESC MCU upgraded to EFM8BB21Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)Support BLHeliSuite programmableFactory firmware: O_H_5_REV16_8.HEXDefault protocol: DSHOT600 Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500HzRF Frequency: 2.4GHz Antenna : SMD antennaTelemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Could bind with Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX module(need to flash the same version ELRS firmware) Onboard 5.8g VTX Output power: 25mw~200mw switchableFrequency: 40CHInput voltage: 3.3V 5.5VCurrent consumption: 300mA(type)Frequency: 5.8GHz 5bands 40 channels(include Race band)Smartaudio ready Onboard voltage and Amperage meters settings Voltage meter scale setting 110 Amperage meter scale setting 1175

Price: 65.44 USD

Location: 深圳

End Time: 2024-08-06T08:55:19.000Z

Shipping Cost: 10 USD