〖US〗3 Axis USB CNC Controller Kit NEMA23 425oz-in 112mm stepper motor driver cnc

Description: 【USA Stock & Fast shipping】〖US〗3 Axis USB CNC Controller Kit NEMA23 425oz-in 112mm stepper motor driver cncfor CNC Router Engraving Milling Machine Good News: We have US Warehouse in USA,so we will ship this product from USA to American Customers directly. Package include: 3 x 23HS2430B Nema23 Stepper Motor Dual Shaft ( 425oz-in,112mm Length ,3A )3 x FMD2740C stepper motor driver1 x 400W 36V 9.7A switching power supply1 x 4 Axis USB CNC breakout board1 x Hand controller1 x USB Cable1 x CD include usbcnc software & registration key 100% Brand New and High Quality!!! This interface board is based on USBCNC MK1 and just use in our provide software and function, cannot support other versions of the software and function 1. 4 Axis USBCNC breakout board 1) Products brief introduction USBCNCV4.0 is a high performance motion controller which based on PC software USBCNC control, the system can complete the conversion from G code to connect stepper motor’s driver motion control signal without requiring any additional hardware and software. This control card is compatible with most stepper driver and servo driver,it is a perfect controller that instead of parallel Mach3 interface board. 2) Computer system requirement Minimum configuration:1) CPU:1GHz2) Memory: 512MB3) 500MB free disk space4) DIRECTX9 graphics device with WDDM 1.0 or higher driver5) USB 2.0 interface6) Net FRAMEWORK 3.5SP1 The recommended configuration:1) CPU:2GHz dikaryon2) Memory: 2GB;3) 1G free disk space4) DIRECTX9 graphics device with WDDM 1.0 or higher driver5) USB 2.0 interface6) Net FRAMEWORK 3.5SP1 3.Production feature 1. After the revision,V4 version using the red PCB board, PCB size is 135.3*82.5mm.;2. The front of the narrow edge placed with USB communication interface and DB9 hand control interface for the convenience of customers drawn from the case panel directly;3. The back-end of narrow edge is power input and output interface and 3 relay output interface; relay is strong interference source, relay away from the design of main control chip, it is conducive to the stability of the board;4. One of the two wide sides is stepper motor and principal axiscontrol signal output;5. The another side of two wide sides is the emergency stop, manual speed input, limiting input interface; one side for the input, another side output connection mode is simple and convenient;6. 5V and 12V power module compact independence, security, stability;7. External ensure the stability of the system work effectively with crystal active and main control chip shield;8.outline dimension is 135.3*82.5mm, product positioning hole installment dimension is 127*75mm9. The software is USBCNC,not mach3,pls note!This item is easy to operate for DIY hobby user,but it is control by USB port,so need more careful for the software install,and pls must be strict read the user manual and follow us. 2. FMD2740C stepper motor driver 1) Brief introductionFMD2740C driver by Japanese sanyo's chip,After multiple optimize R & D and production of high-subdivision 2-phase stepper motor drives, suitable for driving small and medium-sized phase current is less than 4A 2-phase or 4-phase hybrid stepping motor. Due to the adoption of the new bipolar constant current chopper drive technology, using the same motor can output more speed and power than other drivers. Segments stepper motor running accuracy improved, reduces vibrations and noise reduction. 2) Features1. High-performance, low price 2. Bipolar constant current chopping mode3. Power supply voltage 12 to 40VDC 4. High-speed optocoupler signal isolation input5. 20kHz chopping frequency 6. Subdivision precision 2\8\16\32\64\128\10\20 optional 7. Electrical input signal is TTL compatible8. Stationary current is automatically reduced by half9. Shape design is convenient for installation 10.Maximum drive current is 4A11.Drive any 4A phase current of 2-phase or 4-phase hybrid stepping motor 3)ApplicationsSuitable for a variety of small and medium-sized automation equipment and instruments,for example: Small engraving machine, SMT machine, etc. 4) Wiring definedWeak signal interface SignalFunctionSP+Pulse signal + endSP-Pulse signal - endDIR+Direction signal +endDIR-Direction signal-endEN+Enable signal +endEN-Enable signal -end Strengths connection portSignalFunctionVIN+12to50 v dc power supply input +end,it is recommended to use 36V3AGNDDC power supply connection groundA+Stepper motor A + Phase terminalA-Stepper motor A - Phase terminalB+Stepper motor B+ Phase terminalB-Stepper motor B - Phase terminal NOTE: This drive does not contain anti-anti-interpolation circuit so non-input positive and negative power supply upside down! Otherwise it will damage the drive! 5) The electrical characteristics 6) The use of the environment and parameters Cooling methodNatural cooling or forced air cooling Use of the environmentOccasionsAvoid dust, oil mist and corrosive gasesTemperature0°C-+50°CHumidity40-90%RHVibration6m/s2 MAXStorage temperature-20°C-+65°CWeight250g 7) Mechanical installation size8) Power supply The supply voltage can work normally in between DC12V-50V, FMD2740C driver can use ordinary switch DC power supply, can also be used for transformer and the bridge rectifier and filter capacitor, capacitance desirable 2000U to 5000U. Note rectified voltage ripple crest does not exceed 50V.Recommended the user to use the 24V-32V DC supply , avoid the grid fluctuations over drive voltage operating range. Note:1, Wiring should pay attention to the power of positive and negative Do not be reversed;2, In order to reduce costs, multiple drives can share a power supply. But it should improve the rated power and rated output current of the power and attention to cooling. 9)Attenuation of the DIP switch settings Decay modeSW1SW2Slow decayOFFOFFMixed decayONOFFFast decayOFFON 10)Subdivision DIP switch settings 11)Current DIP switch settings 12)Drive motor controller wiring diagram13)Electrical wiringThe FMD2740C driver can drive all current 4A 4-wire, 6-wire or 8-wire 2-phase / 4-phase motors, are detailed below 4-wire, 6-wire, 8 wire stepper motor connection: 14)Matching of the drive and motor FMD2740C driver can drive the domestic and foreign manufacturers of 2-phase or 4-phase motor, in order to obtain the most satisfactory driving, you need to choose a reasonable supply voltage and current setting. Supply voltage determines the level of the high-speed performance of the motor, and the current set value determines the output torque of the motor. Supply voltage selected Generally speaking, the higher the supply voltage, the greater the torque motor at high speed, the more it can avoid the high speed out. But another aspect, the voltage is too high will lead to over-voltage protection, and can even damage the drive, but also in the high-pressure work, low speed vibrations. The output current is setFor the same motor, the greater the current setting, the higher speed, the current motor and drive more heat. So under normal circumstances the current setting into a powered machine warm but not too hot long-term value.Note: the current settings after you run the motor for 15-30 minutes, if the motor temperature is too high, you should reduce the current settings. If the motor current setting, the motor output torque is not enough to improve heat dissipation conditions to ensure that the motor and drive are not hot. 3. Stepper Motor Technical Specifications Part No.: 23HS2430BFrame Size: NEMA23Step Angle: 1.8 degreeCurrent: 3.0A/phaseResistance: 1.6 Ohm/phaseInductance: 6.8 mH/phaseHolding torque:280N.cm/28kg-cm 425 oz-inRotor inertia: 800g-cm2Number of wire leads: 4Weight: 1.66 kgLength: 112mmGeneral Specification:Step angle accuracy:+ - 5%(full step,not load)Resistance accuracy: + - 10%Inductance accuracy:+ - 20%Temperature rise: 80deg Max(rated current,2 phase on)Ambient temperature ----------—20deg ---- +50degInsulation resistance:100ohm Min,500VDCInsultion Strength--------500VAC for one minute Datasheet(23HS2430B,Front shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length,425 oz-in or 28kg.cm holding torque) This product also has a single shaft for choice, the need to invite the message. Wiring: Red: A+Green: A-Yellow: B+Blue: B- 4.Switching power supply400W,Input:100-120VAC or 200-240VAC,50/60Hz,Output:36V,single output switching power supply 5.Usage or Application This products are widely used in engraving machine, printer, medical equipment, embroidery machine, stage lighting, textile automation, printing, packaging and other industries automation equipment. Feedback: We maintain hightest buyer ratings > Positive Feedback will be much appreciated from you. > Any dissatisfaction,please contact us immediately! > Please do not leave neutral or negative feedback before we help you out. Returns: > Defect: We will fully refund or send you a new replacement,please contact and return within 30 days. > Dissatisfaction: Please contact within 3 days, we will fully refund, after got your returned goods. > Missing parts/Q'ty: Please contact us immediately,for a new package arranged,or a partial refund issued. Contact us: > If have any question, Please contact us by ebay message before leaving neutral, negative feedback or open any dispute, we will reply within 24hours, ensure that help you solve the problem, make you satisfied.

Price: 205 USD

Location: Dallas

End Time: 2024-02-18T07:55:12.000Z

Shipping Cost: 0 USD